proServ

The world's first controller that is configured using ONLY the ETS
Info
Application area
The KNiX Port is used as interface to connect to KNX/EIB both on telegram level (KNXnet/IP Tunnelling) and on data-point level (KNX Application Layer).

The connection is made through LAN (IP). The IP Address can be obtained by a DHCP server or by manually configuration (ETS) respectively. As Interface the device works according to the KNXnet/IP specification.

techspecs_title_tech
Connectivity

- 10 simultaneous connections possible (10 mobile Apple devices can be connected at the SAME time)
- 1000 Data-Points can be assigned (to individual group addresses)
- can be used as a programming gateway for the ETS (IP gateway), remote access possible

Electrical safety

- Protection (EN 60529): IP 20

EMV requirements

- Complies EN 61000-6-2, EN 61000-6-3
and EN 50090-2-2

Environmental requirements

- Ambient temp. operating: - 5 ... + 45 °C
- Ambient temp. Non-op.: - 25 ... + 70 °C
- Rel. humidity (non-condensing): 5 % … 93 %

Certification

- EIB / KNX

CE norm

- Complies with the EMC regulations (residential
and functional buildings) and low voltage directive

Physical specifications

- Housing: Plastic
- Rail mounted device, depth 2 units
- Weight: approx. 100 g
- Fire load: approx. 1000 kJ

Operating controls

- Learning key for EIB/KNX

Indicators

- Learning-LED (red)
- Signal-LED (green) for EIB/KNX
- Signal-LED (green) for LAN

Ethernet

- 10BaseT (10Mbit/s)
- Supported internet protocols ARP, ICMP,
IGMP, UDP/IP, TCP/IP and DHCP

Power supply

- External supply 12-24V AC / 12-30V DC
- Alternative: „Power over Ethernet“ (PoE)
- Power consumption: < 800 mW









KNiX Port V2 (250 datapoints)

Interface and ObjectServer between LAN and EIB/KNX-Bus

Application area
The KNiX Port is used as interface to connect to KNX/EIB both on telegram level (KNXnet/IP Tunnelling) and on data-point level (KNX Application Layer).

The connection is made through LAN (IP). The IP Address can be obtained by a DHCP server or by manually configuration (ETS) respectively. As Interface the device works according to the KNXnet/IP specification.

techspecs_title_tech
Connectivity

- 10 simultaneous connections possible (10 mobile Apple devices can be connected at the SAME time)
- 250 Data-Points can be assigned (to individual group addresses)
- can be used as a programming gateway for the ETS (IP gateway), remote access possible

Electrical safety

- Protection (EN 60529): IP 20

EMV requirements

- Complies EN 61000-6-2, EN 61000-6-3
and EN 50090-2-2

Environmental requirements

- Ambient temp. operating: - 5 ... + 45 °C
- Ambient temp. Non-op.: - 25 ... + 70 °C
- Rel. humidity (non-condensing): 5 % … 93 %

Certification

- EIB / KNX

CE norm

- Complies with the EMC regulations (residential
and functional buildings) and low voltage directive

Physical specifications

- Housing: Plastic
- Rail mounted device, depth 2 units
- Weight: approx. 100 g
- Fire load: approx. 1000 kJ

Operating controls

- Learning key for EIB/KNX

Indicators

- Learning-LED (red)
- Signal-LED (green) for EIB/KNX
- Signal-LED (green) for LAN

Ethernet

- 10BaseT (10Mbit/s)
- Supported internet protocols ARP, ICMP,
IGMP, UDP/IP, TCP/IP and DHCP

Power supply

- External supply 12-24V AC / 12-30V DC
- Alternative: „Power over Ethernet“ (PoE)
- Power consumption: < 800 mW






KNiX Port V3 (1000 datapoints)

Interface and ObjectServer between LAN and EIB/KNX-Bus

Application area
The KNiX Port is used as interface to connect to KNX/EIB both on telegram level (KNXnet/IP Tunnelling) and on data-point level (KNX Application Layer).

The connection is made through LAN (IP). The IP Address can be obtained by a DHCP server or by manually configuration (ETS) respectively. As Interface the device works according to the KNXnet/IP specification.

techspecs_title_tech
Connectivity

- 10 simultaneous connections possible (10 mobile Apple devices can be connected at the SAME time)
- 1000 Data-Points can be assigned (to individual group addresses)
- can be used as a programming gateway for the ETS (IP gateway), remote access possible

Electrical safety

- Protection (EN 60529): IP 20

EMV requirements

- Complies EN 61000-6-2, EN 61000-6-3
and EN 50090-2-2

Environmental requirements

- Ambient temp. operating: - 5 ... + 45 °C
- Ambient temp. Non-op.: - 25 ... + 70 °C
- Rel. humidity (non-condensing): 5 % … 93 %

Certification

- EIB / KNX

CE norm

- Complies with the EMC regulations (residential
and functional buildings) and low voltage directive

Physical specifications

- Housing: Plastic
- Rail mounted device, depth 2 units
- Weight: approx. 100 g
- Fire load: approx. 1000 kJ

Operating controls

- Learning key for EIB/KNX

Indicators

- Learning-LED (red)
- Signal-LED (green) for EIB/KNX
- Signal-LED (green) for LAN

Ethernet

- 10BaseT (10Mbit/s)
- Supported internet protocols ARP, ICMP,
IGMP, UDP/IP, TCP/IP and DHCP

Power supply

- External supply 12-24V AC / 12-30V DC
- Alternative: „Power over Ethernet“ (PoE)
- Power consumption: < 800 mW






KNiX Port V2+ (250 datapoints)

Interface and ObjectServer between LAN and EIB/KNX-Bus

Application area
The KNiX Port is used as interface to connect to KNX/EIB both on telegram level (KNXnet/IP Tunnelling) and on data-point level (KNX Application Layer).

The connection is made through LAN (IP). The IP Address can be obtained by a DHCP server or by manually configuration (ETS) respectively. As Interface the device works according to the KNXnet/IP specification.

techspecs_title_tech
Connectivity

- 10 simultaneous connections possible (10 mobile Apple devices can be connected at the SAME time)
- 250 Data-Points can be assigned (to individual group addresses)
- can be used as a programming gateway for the ETS (IP gateway), remote access possible

Electrical safety

- Protection (EN 60529): IP 20

EMV requirements

- Complies EN 61000-6-2, EN 61000-6-3
and EN 50090-2-2

Environmental requirements

- Ambient temp. operating: - 5 ... + 45 °C
- Ambient temp. Non-op.: - 25 ... + 70 °C
- Rel. humidity (non-condensing): 5 % … 93 %

Certification

- EIB / KNX

CE norm

- Complies with the EMC regulations (residential
and functional buildings) and low voltage directive

Physical specifications

- Housing: Plastic
- Rail mounted device, depth 2 units
- Weight: approx. 100 g
- Fire load: approx. 1000 kJ

Operating controls

- Learning key for EIB/KNX

Indicators

- Learning-LED (red)
- Signal-LED (green) for EIB/KNX
- Signal-LED (green) for LAN

Ethernet

- 10BaseT (10Mbit/s)
- Supported internet protocols ARP, ICMP,
IGMP, UDP/IP, TCP/IP and DHCP

Power supply

- External supply 12-24V AC / 12-30V DC
- Alternative: „Power over Ethernet“ (PoE)
- Power consumption: < 800 mW









KNiX Port V3+ (1000 datapoints)

Interface and ObjectServer between LAN and EIB/KNX-Bus

Application area
The KNiX Port is used as interface to connect to KNX/EIB both on telegram level (KNXnet/IP Tunnelling) and on data-point level (KNX Application Layer).

The connection is made through LAN (IP). The IP Address can be obtained by a DHCP server or by manually configuration (ETS) respectively. As Interface the device works according to the KNXnet/IP specification.

techspecs_title_tech
Connectivity

- 10 simultaneous connections possible (10 mobile Apple devices can be connected at the SAME time)
- 1000 Data-Points can be assigned (to individual group addresses)
- can be used as a programming gateway for the ETS (IP gateway), remote access possible

Electrical safety

- Protection (EN 60529): IP 20

EMV requirements

- Complies EN 61000-6-2, EN 61000-6-3
and EN 50090-2-2

Environmental requirements

- Ambient temp. operating: - 5 ... + 45 °C
- Ambient temp. Non-op.: - 25 ... + 70 °C
- Rel. humidity (non-condensing): 5 % … 93 %

Certification

- EIB / KNX

CE norm

- Complies with the EMC regulations (residential
and functional buildings) and low voltage directive

Physical specifications

- Housing: Plastic
- Rail mounted device, depth 2 units
- Weight: approx. 100 g
- Fire load: approx. 1000 kJ

Operating controls

- Learning key for EIB/KNX

Indicators

- Learning-LED (red)
- Signal-LED (green) for EIB/KNX
- Signal-LED (green) for LAN

Ethernet

- 10BaseT (10Mbit/s)
- Supported internet protocols ARP, ICMP,
IGMP, UDP/IP, TCP/IP and DHCP

Power supply

- External supply 12-24V AC / 12-30V DC
- Alternative: „Power over Ethernet“ (PoE)
- Power consumption: < 800 mW